Do you use thread tape on philmac fittings?

Do you use thread tape on philmac fittings?

Philmac recommends the use of PTFE tape on threads to ensure a positive seal.

Can philmac fittings be used on hot water?

Wide range: The new 3G™ compression fitting range is comprehensive and includes straight and reducing joiners, tees, elbows, male and female adaptors and caps ranging from ½” to 2”. CAUTION: Philmac does not recommend or warrant the use of 3G™ Compression Fittings “inside the building” or for “hot water” applications.

Do philmac fittings need inserts?

For connections to imperial PE pipe (BS1972/3284 and IRS 135 Heavy Gauge) a liner or insert is not required. The fitting is pre-assembled and ready to use, however always ensure the nut is fully relaxed and 2 threads are showing before inserting the pipe.

What are philmac fittings?

Philmac threaded fittings are manufactured from high performance, UV resistant polypropylene material that prevents moisture absorption and sustains product dimensions. The chemical and corrosion resistance provides a reliable and long life for the fitting. Browse fittings. Valves.

How do you remove a philmac fitting?

Philmac 3G fittings are easily disassembled by simply loosening the nut until two threads are showing. The pipe will be released and can simply be pulled out of the fitting. Care must be taken not to cut the pipe too short as it is essential to draw the pipe into the fitting when making a joint.

How do you connect PE pipes?

PE pipe can be assembled into a pipeline network by means of fusion or mechanical assembly techniques. Fusion of PE pipe and fittings may be by either Butt Fusion or Electrofusion. Other techniques are available (socket fusion and induction fusion) but are not commonly available and will not be considered here.

How do you connect PPR pipe to PE pipe?

The PPR pipe and PE pipe should not be connected by hot melt. The PPR Female Adapter should be directly connected with the PPR Male Adapter. The wall thickness of PE tube is different from that of PP-R tube. The bonding strength of the two materials cannot meet the requirements.

Do you use thread tape on Poly fittings?

With poly fitting, you do need more thread tape. I normally use about 20-30 laps depending on the fitting. Leave the first couple of threads relatively free of tape ( 1-5 laps) and put the tape on so that i forms a kind of cone shape, ie thicker at the back than front.

Do you put plumbers tape on plastic fittings?

Do use a sealant. Teflon tape, Teflon paste and pipe dope is intended for metal pipe and fittings. Metal to metal fitting joints are more difficult to tighten than plastic; the surfaces tend to gall without the aid of such lubricants as Teflon or pipe dope. Plastic fittings do not need this lubrication.

Can you use brass compression fittings on polyethylene tubing?

Compression fittings are not recommended to be used with steel tube. When using compression fittings with any type of plastic tubing, a brass insert must be used for further support.

Will compression fittings work on polybutylene?

Qest compression fittings by Zurn can be used to connect gray polybutylene, PEX, CPVC or copper tubing in any combination. These are one of the few fittings that can be used with gray polybutylene plastic tubing. Polybutylene was often used in manufactured homes.

Where are philmac fittings made?

Adelaide, South Australia
Philmac, proudly developed & manufactured in Adelaide, South Australia, offers a wide range of fittings and valves to cover most PE pipe applications.

How PPR pipes are joined?

Instead of PVC cement, PPR joints are heated by a special fusion tool and essentially melted together into a single piece. When created properly using the right equipment, a PPR joint will never leak.

Why choose philmac fittings?

Philmac manufactures a range of fittings designed to make installation a simple as possible without compromising any long term performance. Philmac designs and manufactures a range of high quality fittings and valves for most PE pipe standards.

What is philmac UTC compression fitting?

Philmac UTC (Universal Transition Coupling) is a unique range of compression fittings that provides the ultimate in pipe connection flexibility. The Philmac SIDR fitting range provides an easy connection and disconnection fitting with maximum flexibility.

How do you install a philmac BSP?

INSTALLATION INSTRUCTIONS – POLY Note: Philmac recommends the use of PTFE tape on BSP threads to ensure a positive seal. 1. Cut Pipe Square Cut the pipe square. There is no need to prepare the pipe end. Chamfering or lubrication is not required.

Where can I find philmac’s 3G metric™ technical manual?

18 3G METRIC™ TECHNICAL MANUALd m m Philmac Pty Ltd 53-59 Deeds Road North Plympton South Australia AUSTRALIA 5037 Telephone +61 (8) 8300 9200 Facsimile +61 (8) 8300 9390 www.philmac.com.au wdm_21705